Setup and Climate Control

How to Set Up Drip Irrigation in a Greenhouse

Set up drip irrigation in a greenhouse step by step: the parts you need, how to plan zones, install tubing and emitters, add a timer and avoid winter freezes.

On this page
  1. Why use drip irrigation in a greenhouse
  2. What you need
  3. Step 1: Plan your zones
  4. Step 2: Connect at the source
  5. Step 3: Lay the main line
  6. Step 4: Add branches and emitters
  7. Step 5: Flush and test
  8. Step 6: Set the schedule
  9. Winter and freezing
  10. Troubleshooting and upkeep

Why use drip irrigation in a greenhouse

Drip irrigation delivers water slowly to the root zone through tubing and emitters. Compared with overhead watering it can reduce evaporation and waste, keeps foliage drier (which may reduce some fungal problems), and saves time, especially when paired with a timer. It also helps with humidity, since less water is splashed or sprayed into the air (see how to control humidity in a greenhouse).

For a few pots, hand watering may be simpler. Drip pays off when you have many containers, grow in beds, or are away often.

What you need

From the water source outward, a typical setup includes:

Part What it does
Timer (optional but handy) Turns water on and off automatically
Backflow preventer Stops water flowing back into your supply, which matters especially if you add fertilizer
Filter Removes particles that can clog emitters
Pressure regulator Drip systems generally run at low pressure, often around 20 to 30 PSI, much lower than household supply
Main line tubing (often 1/2 inch) Carries water through the greenhouse
1/4 inch distribution tubing Branches to individual plants or pots
Emitters or drippers Release water at a set rate, such as 1/2 or 1 gallon per hour
Drip tape or inline emitter tubing Waters rows of plants evenly
Connectors, tees, elbows, end caps, stakes and plugs Join, secure and repair the lines

Kits for small greenhouses bundle most of these, and following the kit’s instructions for pressure and run length is wise.

Step 1: Plan your zones

Group plants with similar water needs. A thirsty tomato bed shouldn’t share a line with drought-tolerant herbs, and seedling trays may need different treatment from large containers. Sketch the greenhouse, mark pots, beds and benches, and plan where the main line will run. Keep long runs within the limits recommended for your tubing so pressure stays even. Also consider how you’ll move around, so tubing doesn’t become a trip hazard.

Step 2: Connect at the source

  1. Attach the timer to the tap or supply, if you’re using one.
  2. Add the backflow preventer.
  3. Fit the filter. Finer mesh helps protect small emitters.
  4. Add the pressure regulator.
  5. Connect the main line.

Use the correct adapters and check for leaks at each joint.

Step 3: Lay the main line

Run the main tubing along walls, bench edges or beds, and secure it with clips or stakes. Keep it away from walkways and avoid kinks. Tubing left in sunlight can become brittle over time, so take care to protect it if it is exposed.

Step 4: Add branches and emitters

  • Containers: punch a hole in the main line with a punch tool, insert a connector, and run 1/4 inch tubing to each pot with a dripper or stake at the end. Larger pots may need two emitters.
  • Beds and rows: use drip tape or inline emitter tubing along the row.
  • Benches: run a line along the bench with branches to trays or pots. Use drainage trays or slatted tops to prevent pooling (see greenhouse bench and staging systems).
  • Hanging baskets: use drippers on individual lines, and expect these to dry faster.

Match the emitter rate to the plant and container size. Check the maker’s guidance.

Step 5: Flush and test

Before closing the ends, run the water for a few minutes to flush out debris. Then fit end caps, check each emitter is dripping, look for leaks and make sure every plant is getting water. Adjust positions as needed.

Step 6: Set the schedule

Start with short, regular watering and watch how the soil responds. Check moisture by finger or with a meter, since plant needs change with temperature, light, plant size and season. Water in the morning where possible. A timer makes this consistent, but it doesn’t replace checking the plants. Soil moisture sensors can be added if you want the system to respond to actual conditions.

Winter and freezing

Water in lines can freeze and damage tubing, fittings and timers. In cold weather, don’t leave the supply on if freezing is possible, drain or disconnect lines, bring timers indoors, and don’t turn the water on until the greenhouse is warm enough. Cold, wet soil dries slowly, so reduce watering and avoid overwatering (see how to keep a small greenhouse warm at night for frost protection ideas).

Troubleshooting and upkeep

  • Clogged emitters: clean or replace them, and check the filter.
  • Uneven watering: may signal low pressure, long runs or blocked lines.
  • Leaks: check joints, punctures and end caps, and plug unused holes.
  • Misting or blown fittings: pressure may be too high, so check the regulator.
  • Algae in lines: flush periodically.
  • Mixing sprinklers and drippers on one zone: avoid, as they need different pressures.

Check the system as part of regular upkeep (see the greenhouse maintenance checklist). For the wider picture of planning a greenhouse, see setting up a small greenhouse.

The complete guide to setup and climate control

Setting Up and Designing a Small Greenhouse
Read the guide

Keep exploring

Guides from other topics

All topics →