What a greenhouse base needs to do
A good base does four jobs. It holds the frame level and square, so doors, vents and glazing fit properly. It gives something solid to anchor to. It lets water drain away rather than pool around the structure. And it keeps the frame off bare, damp ground where timber rots and metal corrodes.
Many kits specify a base size and type, and the instructions usually include the permitted tolerance for level and square. Follow those first. The rest of this article covers general principles.
Base options compared
| Base | Best for | Pros | Cons |
|---|---|---|---|
| Compacted gravel pad | Small and light greenhouses, good drainage | Inexpensive, drains well, easy to DIY | Needs an edging or frame for fixing; does not anchor on its own |
| Timber perimeter frame | Small to medium kits, mildly uneven ground | Cheap, adjustable, familiar to DIYers | Wood can eventually rot; needs a level bed beneath it |
| Concrete perimeter or block footing | Medium and larger builds, windy sites | Strong anchor, pest-resistant, leaves the interior open for soil | More labor and cost; harder to change later |
| Full concrete slab | Large, permanent or glass structures | Very rigid, easy to clean | Most expensive; limits planting in the ground; needs drainage planning |
| Steel or resin kit base | Matching a specific kit | Fits the footprint, quick to install | Still needs a level bed and fixing down |
For heavy glass greenhouses or places with deep winter frost, a properly built concrete foundation is the more common recommendation. In cold climates, footings may need to reach below the local frost depth, so check local guidance.
Can I put my greenhouse on grass?
You can for a small, light, temporary structure, but it is not ideal. Grass and soil are rarely level, the frame can twist as the ground moves, and bare grass under a greenhouse tends to turn into a damp, weedy patch. If you do put one on grass, at least remove the turf, level the area and set the frame on a timber or steel base pinned into the ground. For anything bigger than a small hobby greenhouse, a proper base is worth the effort.
How to build a DIY base (step by step)
These steps apply to a timber or gravel-and-timber base for a small to medium greenhouse.
- Check the rules and the ground. Look into local building or HOA rules, and locate any buried pipes or cables before you dig. See do I need a permit for a backyard greenhouse.
- Choose the spot. Pick a level area with plenty of light, reasonable drainage and easy access to water. See placing a greenhouse in your garden or allotment.
- Mark the footprint. Use stakes and string. Measure both diagonals; the layout is square when they are equal.
- Excavate. Remove sod, roots and organic soil, and level the area. Lay landscape fabric if you want weed control.
- Add a drainage layer. Spread and compact crushed stone (angular stone compacts better than rounded pea gravel).
- Build the frame. Use rot-resistant timber, such as pressure-treated lumber or a naturally durable wood, or a steel base kit. Join the corners, level in both directions and re-check the diagonals.
- Pin the base down. Drive rebar or ground anchors through the frame into the soil. More detail is in how to anchor a greenhouse against wind.
- Check again before assembly. Re-measure level and square once everything is fixed. It is far easier to correct now than after the greenhouse is up.
For a concrete slab, the same principles apply, with formwork, a compacted sub-base, reinforcement and curing time before you build on it. If you haven’t poured concrete before, many people hire this part out.
Choosing by size, soil and climate
- Small, lightweight greenhouse on well-drained soil: gravel with a timber or steel base is often enough.
- Windy site: prioritize a strong, positive connection between frame and foundation.
- Heavy clay or wet ground: drainage matters most; use a gravel bed beneath the base and consider where water will go.
- Cold climate: check frost depth, and consider whether the greenhouse will be heated, since heat can affect the ground beneath it.
- Glass: heavier glazing generally calls for a more rigid base. See greenhouse glazing: glass, polycarbonate and FRP and glass greenhouse plans.
The inside floor is a separate decision from the base. See what is the best floor to have in a greenhouse?
Is it cheaper to build or buy?
It depends on your skills, materials and the size. A DIY base is usually cheaper than paying a contractor, and buying materials in bulk from a landscape supplier is often cheaper than small bags. Prices vary a lot by region, so get a few local quotes before deciding. A greenhouse kit is often easier and more predictable for beginners, while a fully custom build can cost less in materials but takes more time and skill. For the whole greenhouse, see is it cheaper to build or buy a greenhouse.
Common mistakes
- Skipping the diagonal check and ending up with a twisted frame.
- Using soft or untreated timber on the ground.
- Building on poorly draining soil without a gravel layer.
- Forgetting to run water or electrical conduit before the base is finished.
- Making the base only the size of the kit, with no room for a path around it.
For an overview of how the base fits with the rest of the structure, see greenhouse structure: parts and components explained.