Short answer
To glaze a greenhouse, you fit panes or panels into the frame and hold them with clips, glazing bars, caps or fixings, then seal them against weather. The details depend on the material. Glass is usually clipped or bedded into the glazing bars, polycarbonate panels slot into profiles or are screwed down with washers, and film is stretched and fastened to the frame. Always follow the manufacturer’s instructions first, because frame designs differ.
If you are still choosing a material, see greenhouse glazing: glass, polycarbonate and FRP.
Before you start
Tools and materials (varies by material):
- Tape measure, level and marker
- Drill, screwdriver and the correct fixings
- Glazing clips, bars or caps, as supplied with the kit
- Glazing strip, sealing tape or a suitable sealant
- Utility knife or fine-toothed saw, for cutting plastic panels
- Gloves and safety glasses; for glass, add cut-resistant gloves
Preparation:
- Check the frame is square and secure. Glazing a twisted frame causes gaps and can crack panes.
- Clean the frame and remove sharp burrs or old sealant.
- Check the weather. Calm, dry conditions are much safer, especially for roof work.
- Work with a helper for large panes or sheets, and use a stable ladder or platform.
Glazing with glass
- Order and start point. Many guides work from the bottom upward on sloped roofs so that each upper pane overlaps the one below it and water runs off. Follow your kit’s instructions for the sequence.
- Seat the pane. Place it into the glazing bar groove or against the rebate. Use the glazing strip, tape or sealant that your frame specifies. Modern greenhouses rarely use traditional putty.
- Hold it with clips or beads. Glass clips (spring clips) or beading secure it. Don’t force the pane; it should sit without strain.
- Overlap if required. Roof panes in some designs overlap slightly, with clips holding the overlap. Leave the overlap that the manufacturer recommends.
- Check the fit. Make sure panes aren’t touching metal or each other in a way that could stress them.
Safety: use toughened glass where possible, carry panes upright, and handle edges with gloves. Dispose of broken glass safely. For a full glass build, see glass greenhouse plans.
Glazing with polycarbonate panels
- Cut to size if needed, following the direction of the channels (flutes) and using a fine-toothed saw or knife. Leave the protective film in place while cutting.
- Check the orientation. Many sheets have a UV-protective layer on one side. Fit it facing outward as marked.
- Run the flutes vertically on roof slopes and walls, so condensation and water drain out.
- Fit into profiles or fix down. Panels slide into H-profiles or are held by caps and glazing bars. If screwed, use the correct washers and don’t overtighten.
- Allow for expansion. Sheets expand and contract with temperature, so leave the gaps recommended by the maker.
- Seal the ends. Cover the top ends with solid tape and the bottom ends with vented tape, if instructed, so dust and insects stay out and moisture can drain.
- Peel the protective film after fitting.
For framing and fastening in more depth, see how to build a greenhouse with polycarbonate panels.
Covering with polyethylene film
- Choose greenhouse-grade, UV-stabilized film that is slightly oversized.
- Pick a mild, still day, ideally a warm one so the film tightens as it cools.
- Drape the film over the frame and fasten it along the base, then the ends.
- Use channel-and-wire locking systems, battens or tape, and pad sharp edges so they don’t tear the film.
- Pull it tight, but not so much that it is overstretched.
Film is the usual cover for a hoop house over a raised bed or a polytunnel.
Common mistakes
- Glazing before checking that the frame is square.
- Fitting polycarbonate with the UV face inward.
- Over-tightening screws, causing cracks or tearing.
- Leaving no room for thermal expansion.
- Not sealing panel ends, letting dirt and algae in.
- Using unsuitable sealant that damages the glazing or the frame. Check the product for compatibility.
Maintenance after glazing
Clean glazing gently with warm water and a soft cloth or brush, since scratches reduce clarity and abrasive cleaners can damage plastic. Check clips, seals and panels each season, and after storms replace anything loose or cracked. These checks fit into a greenhouse maintenance checklist. For rooflines, vents and the other parts you’ll be glazing around, see greenhouse roof vents and ventilation and greenhouse structure: parts and components explained.