DIY Greenhouse Building

How to Build a Greenhouse with Polycarbonate Panels

How to glaze a DIY greenhouse with polycarbonate panels: choosing thickness, framing to the panel width, UV side, sealing flutes and fastening for expansion.

On this page
  1. Why polycarbonate
  2. Panel types and thickness
  3. Plan the frame around the panels
  4. Before installing
  5. Cutting
  6. Sealing edges
  7. Fastening, with room to expand
  8. Step-by-step installation
  9. Common mistakes

Why polycarbonate

Polycarbonate panels are light, tough and insulate better than single-pane glass or a single layer of film. They are a popular DIY glazing because they are easier to handle than glass, resist breakage and give diffused light. They also scratch more easily than glass, can pick up dust and algae, and need careful installation to allow for thermal movement. For how polycarbonate compares with glass and FRP, see greenhouse glazing, and for its drawbacks, the disadvantages of a polycarbonate greenhouse.

Panel types and thickness

  • Twin-wall (double-wall) panels have two skins joined by ribs, creating air channels called flutes. They are the most common and affordable choice.
  • Triple-wall and multiwall panels have more layers and insulate better, but transmit somewhat less light. One builder who installed 16 mm triple-wall panels in a cold-climate greenhouse chose them for their insulation, and decided against a more insulating multiwall type because light was a bigger concern in winter.
  • Corrugated and single-skin panels are cheaper, with less insulation.

Thicker panels insulate better but cost more and are less flexible. Panel makers publish insulation and light transmission figures, so compare those for the products you can buy locally. For cold-climate or winter use, see building a year-round solar greenhouse.

Plan the frame around the panels

Polycarbonate sheets come in standard widths, commonly about 4 feet, so it is easiest to design your frame around the sheet size. Space studs or rafters so that the edges of each sheet land on framing, which usually means spacing the frame to the sheet width, allowing a small gap between sheets for fasteners and movement. Check your supplier’s installation guide, because spacing and recommended screw positions vary between products.

Pressure-treated or rot-resistant lumber works for the frame, and metal framing also suits. See the wood-frame greenhouse guide for framing, and add horizontal blocking where panels need support. A steeper roof sheds water and snow better, and gives you room for a ridge vent. See the best roof pitch for a greenhouse.

Before installing

  • Store panels flat, shaded and dry. Direct sun on stacked sheets can cause heat build-up and make the protective film hard to remove later.
  • Leave the protective film on until the panel is fixed in place. It protects the surface, and usually indicates the UV-protected side.
  • Face the UV side outward. One side of the panel carries a UV-protective layer, and the film is usually marked. Installing it the wrong way round can shorten the panel’s life.
  • Run the flutes vertically on walls and along the slope on roofs, so that moisture and condensation can drain.

Cutting

Cut with a fine-tooth blade on a circular saw or a utility knife for thinner panels, supporting the sheet fully to prevent vibration, and keeping the film on while cutting. Wear eye protection and remove dust from the flutes afterwards with compressed air or a gentle brush.

Sealing edges

The open ends of multiwall panels allow dust, insects and moisture into the flutes. Seal them:

  • Top edge: use solid aluminum tape, so water cannot enter.
  • Bottom edge: use breathable anti-dust tape, so condensation can escape.
  • Then cap the edges with U-channel or an end cap, and use H or J profiles where panels join.

Avoid letting sealant run into the flutes, and check that any silicone is compatible with polycarbonate, since some products damage it. Always follow the panel manufacturer’s recommendations.

Fastening, with room to expand

Polycarbonate expands and contracts with temperature, more than many people expect. To allow this:

  • Use screws with rubber or neoprene washers, designed for polycarbonate.
  • Drill pilot holes slightly larger than the screw shaft.
  • Do not overtighten. The washer should seal without crushing the panel.
  • Use foam sealing tape or gasket between the panel and the frame, which cushions the panel and keeps the join weathertight.
  • Where possible, fix panels with cap bars and channels that clamp the panel edges without drilling through the sheet.

Step-by-step installation

  1. Dry-fit a panel and check that the edges land on framing.
  2. Apply sealing tape to the frame, or to the panel, depending on the system.
  3. Cap the panel edges before fixing them, if using end caps.
  4. Position the panel with the UV side out, starting from one end of the wall or roof, or from the middle in a symmetrical design.
  5. Fasten at the recommended spacing with the correct washers.
  6. Remove the protective film from the outside once the panel is secure, and from the inside where needed.
  7. Add trim, ridge caps and flashing where roof and wall meet. If you are attaching panels near a wall, see how to build a lean-to greenhouse.
  8. Check door and vent seals. See how to build a greenhouse door that seals well.

Common mistakes

  • Installing the UV side inward.
  • Tightening screws too far and cracking panels.
  • Forgetting to allow expansion, so panels buckle on hot days.
  • Leaving flutes open, so algae grows inside.
  • Using incompatible sealants or cleaners. Use mild soap and water, and avoid abrasive cleaners.

The complete guide to diy greenhouse building

How to Build a Backyard Greenhouse
Read the guide

Keep exploring

Guides from other topics

All topics →