DIY Greenhouse Building

How to Build a Cold Frame for Extending the Season

Build a simple cold frame to extend your growing season: design basics, materials, step-by-step plans, no-cut options, venting rules and what to grow inside.

On this page
  1. What a cold frame does
  2. Design basics
  3. Materials and tools
  4. Steps
  5. No-cut options
  6. Using it: venting, watering and crops
  7. Hardening off

What a cold frame does

A cold frame is a bottomless box with a transparent lid, set over the soil. It acts as a miniature greenhouse: sunlight enters, warms the soil and air inside, and the walls shelter plants from wind. Gardeners use cold frames to start the season earlier, to grow cold-hardy crops later into fall and winter, and to harden off seedlings. One experienced gardener describes the inside as typically about 5 to 10 degrees Fahrenheit warmer than outdoors, though the exact difference varies with weather and construction. Cold frames need no power, and many people build one in an hour or two. To decide between the two structures, see cold frame vs greenhouse.

Design basics

  • Slope. Build the back taller than the front so the lid slopes toward the low winter sun and sheds rain and snow. Face the low side south in the Northern Hemisphere.
  • Lid. Glass (such as an old window sash), acrylic, twin-wall polycarbonate or heavy clear plastic all work. Plastic can be cut to any size, while a salvaged window may dictate the size of the box. If you use old windows, see the lead paint caution in building a small greenhouse cheaply.
  • Hinges and a prop. Hinge the lid at the back so you can lift it for venting, and use a stick, notched board or stay to hold it open.
  • Size. Keep it small enough to reach every plant and to move or store easily. A frame about 3 to 4 feet wide suits many beds, and larger frames hold heat less well.
  • Wood. Use rot-resistant or untreated boards, since many gardeners prefer to avoid pressure-treated wood close to edible plants. Cedar is a popular but pricey choice.

Materials and tools

  • Boards or plywood for the walls, such as 1x8 lumber or plywood
  • Corner pieces, such as 2x2s or 1x2s, to join the walls
  • A window or a lid frame covered in clear plastic or polycarbonate
  • Two hinges, a handle and a prop stick
  • Exterior screws
  • Saw, drill, tape measure, square and pencil

Steps

  1. Size the box to the lid. Measure the outside dimensions of your window or lid frame. The box should match it.
  2. Cut the walls. Choose a front height and a taller back height. As an example, one popular plan uses a front of about 7 inches and a back of about 12 inches for a 4-by-4-foot frame, but a taller frame suits taller plants. Cut the front and back boards to the lid width, and cut each side board so that it slopes from the back height down to the front height.
  3. Cut corner supports slightly shorter than the walls so they do not interfere with the lid closing.
  4. Assemble the box. Pre-drill, then screw the walls to the corner pieces to make a sturdy, bottomless frame.
  5. Attach the lid. Place the lid on the box with the higher edge at the back. Screw the hinges to the lid and the back wall. A scrap board inside the back wall gives the screws more to grip. Fit a handle at the front.
  6. Position it. Set the frame in a sunny, sheltered spot facing south. If it sits on a raised bed, fill any gap between the frame and the soil with straw or mulch to keep heat in.

A hardware store will often cut boards to size when you buy them, which saves time if you have no saw.

No-cut options

  • Straw bale frame: stack bales around a bed and set an old window on top. It is cheap and needs no tools.
  • Cinder block frame: stack blocks as walls and top with a clear lid.
  • Window sash on a bed edge: lean a window against a raised bed’s side wall, with bricks as supports.

Using it: venting, watering and crops

  • Vent on sunny days. Cold frames heat up quickly, even in cold weather, and overheating causes soft growth and can burn plants. Prop the lid open a few inches in the morning and close it before the sun goes down. One experienced grower recommends venting any day when the outdoor temperature is above about 40°F, and keeping the lid closed in colder spells except when harvesting.
  • Water carefully. Rain cannot reach inside, but plants need less water in cool weather, so check soil moisture before watering.
  • Close tightly on frosty nights. For extra protection, lay a blanket or row cover over the lid on very cold nights.
  • Good crops: leafy greens such as spinach, lettuce, kale and arugula, root crops such as carrots, beets and radishes, young brassicas and hardy herbs. See growing food in a winter greenhouse for more cold-season crop ideas.

Hardening off

A cold frame is ideal for hardening off seedlings in spring. Open the lid slightly at first, then wider and for longer each day, until the plants are ready to go without it. For seed-starting dates, see when should I start seeds in my greenhouse. For a larger, longer-lasting cover over a bed, try a hoop house over a raised bed.

The complete guide to diy greenhouse building

How to Build a Backyard Greenhouse
Read the guide

Keep exploring

Guides from other topics

All topics →