Door design decisions
The door is the part of a greenhouse that gets used the most, and it is often where heat leaks out and pests get in. A good door is wide enough for your tools, rigid enough not to sag, and closes against a continuous seal. Before you build, decide:
- Hinged or sliding. A hinged door is simplest to build and seals more easily. A sliding door saves swing space but is harder to seal and needs a good track.
- Swing direction. Many people hang the door to open outward, which saves floor space inside and keeps it from hitting benches. Think about wind, snow and where you stand when you open it.
- Solid or glazed. A glazed door lets in light, but a framed door with a solid lower panel is more durable.
Size and opening
Make the opening large enough for the things you carry in. A wheelbarrow, large pots or a bench may need a wider door than you would use for a person alone. Many builders go wider and taller than a standard house door, but a larger door is heavier and more likely to sag. Frame the opening in your greenhouse wall with a header across the top, and trimmer studs on each side, then measure the finished opening before cutting door parts. Build the door slightly smaller than the opening, leaving a small gap on each side for clearance and seals. Square and plumb the opening first, since a crooked frame is the most common reason a door fits badly. The wood-frame greenhouse guide explains how to frame the opening as part of the walls.
Materials
- Rot-resistant or properly sealed lumber for the door frame, such as 2x4s or 2x3s
- A piece of lumber for a diagonal brace
- Exterior wood glue and screws
- Glazing that matches the rest of the greenhouse (polycarbonate, glass or film) or a solid panel
- At least two strong exterior hinges, three for a heavy door
- A latch or hook, and a handle
- Weatherstripping and a door sweep
- A threshold or door stop
Build the door frame
- Cut the parts. You need two vertical stiles and at least two horizontal rails, top and bottom. A middle rail adds stiffness, and holds glazing.
- Assemble a rectangle. Join the rails to the stiles using screws and glue, with corner brackets or half-lap joints for strength. Keep the frame flat on a level surface and check it is square by measuring both diagonals. The two should match.
- Add a diagonal brace. A diagonal brace running from the bottom hinge corner up to the top latch corner stops the door from racking and sagging. This is the single most useful step for a door that stays true over time.
- Seal the wood. Paint or seal the lumber, particularly the end grain and the bottom edge, which absorb moisture.
Glaze the door
Fit the glazing into the frame, using the same material as the rest of the structure if you can, so expansion and light are consistent. Rigid panels need a small gap and trim to hold them in place, and edges need sealing so that moisture does not get in. See building with polycarbonate panels for edge-sealing methods, and glass greenhouse plans if you plan to use glass, which makes a heavy door. For film, stretch it over the frame and secure it with battens.
Hang it
- Fit the hinges to the door and the opening. Mount the top and bottom hinges close to the ends, with a middle hinge for tall or heavy doors. Use screws long enough to reach solid framing.
- Support the door on shims or blocks while you attach the hinges, so the gaps are even.
- Check the swing. The door should move freely without rubbing, and it should hang square in the opening. Adjust the hinges as needed.
Seal it
A door that closes well still leaks heat if the seals are poor. Draw on these:
- Door stop and weatherstripping. Fix a stop strip to the frame so the door closes against it, then add compressible weatherstripping along the stop or door edge. Check that the door can still close without forcing it.
- Door sweep or threshold. A sweep on the bottom edge, or a threshold the door closes against, blocks drafts, rodents and insects. Make sure it does not catch on the floor. See do greenhouses attract rodents.
- Seal the frame to the wall. Fill any gaps between the door frame and the greenhouse wall with sealant or trim.
- Check in the dark. On a bright day, look for light at the edges of the closed door, from the inside, because light shows where air can pass.
Good sealing matters most when you want to retain heat. See do greenhouses work in winter and how to heat a greenhouse in winter without electricity.
Latch, wind and pests
- Use a positive latch such as a hook-and-eye, a barrel bolt or a gate latch. In windy places, a door that blows open can damage the glazing and hinges.
- Add a hold-open hook for warm days, so the door stays open for ventilation without banging. For other ways to keep temperatures down, see how to cool a greenhouse in summer without air conditioning.
- Consider a double system in summer: a screen door or insect mesh fitted outside the main door lets you leave the door open for air while keeping pests out.
- Check hardware each season. Tighten loose screws, replace worn weatherstripping and re-hang a sagging door before the cold weather. These checks fit into a wider greenhouse maintenance checklist.
For the wider design picture, see our guide to building a backyard greenhouse.