DIY Greenhouse Building

How to Build a Lean-To Greenhouse Against Your House

How to build a lean-to greenhouse against a house wall: choosing the wall, checking rules, framing, flashing, glazing and managing moisture and ventilation.

On this page
  1. Why a lean-to
  2. Choose the wall
  3. Check rules and the house first
  4. Design basics
  5. Steps
  6. Moisture, flashing and ventilation
  7. Heating and use

Why a lean-to

A lean-to greenhouse has one side supported by an existing wall, usually of your house, garage or shed. Because it needs only three new walls and a single sloping roof, it generally uses fewer materials than a freestanding structure. The wall also gives a degree of shelter, and a masonry wall can absorb daytime heat and release it at night. It is easy to reach from indoors if you add a connecting door, and it can share some of the house’s warmth.

The trade-offs are less light (the wall blocks one side), a risk of moisture damage to the house wall if details are poor, and stricter rules in many areas for attached structures. If you would rather buy than build, see lean-to greenhouse kits.

Choose the wall

In the Northern Hemisphere, a south-facing wall (or one close to it) gives the most winter sun. East and west walls get some light, but a north wall is rarely suitable for growing. Look for a wall with no tall trees or buildings that shade it in winter. A light-colored wall reflects extra light into the greenhouse, and a dark masonry wall stores more heat.

Check what the wall is made of. Brick, block and concrete are easier to attach to and handle moisture better than wood siding or stucco. If the wall has windows or doors, think about whether the greenhouse will cover them.

Check rules and the house first

  • Permits. An attached structure is more likely than a freestanding one to need approval. See do I need a permit for a backyard greenhouse.
  • Utilities. Find out what runs through the wall or under the site: gas meters, electrical panels, vents, dryer exhausts and water lines. Do not block gas meters, vents or exhausts.
  • Roofline and gutters. Consider where water will drain, and whether the greenhouse roof ties in below eaves or windows. See greenhouse gutters and rainwater collection.
  • Structure. If you are not sure the wall can support a ledger board, ask a builder or engineer. Attaching a structure to a house is a part of the project where professional advice is worth having.
  • Insurance and HOA rules may also apply.

Design basics

  • Roof slope. A single-slope roof running from a high point at the wall down to a lower front wall sheds rain and snow away from the house. Check your local snow load and aim for a slope that is steep enough to shed water. See the best roof pitch for a greenhouse.
  • Size. Depth is often limited by wall height and roof slope. Width can run along as much of the wall as you like.
  • Foundation. A timber base on gravel, concrete blocks or a slab are all used. A frost-resistant footing is better for permanent structures. Compare greenhouse base and foundation options.
  • Glazing. Multiwall polycarbonate is common because it is light and insulating, and it handles a sloped roof well. See how to build a greenhouse with polycarbonate panels. Glass also works if your frame is strong enough.
  • Door and vents. Place the door at one end, or connect through an existing door, and put vents high at the front or roof.

Steps

  1. Mark the footprint against the wall and prepare a level base. Contact your utility locating service before digging.
  2. Build the base and check that it is square and level. Allow for drainage so that water does not pool against the house.
  3. Attach a ledger board to the wall at the roof line, using fasteners suitable for the wall type, and with flashing above it (see below). This is the point where a professional’s advice is most valuable.
  4. Frame the front wall and end walls, including the door and any windows.
  5. Add rafters that run from the ledger down to the front wall plate, spaced to suit your glazing, and tie them with metal brackets.
  6. Brace the frame diagonally so that it is stiff before glazing.
  7. Install flashing where the roof meets the house wall, before the glazing, so that water runs out and over rather than behind. One builder noted that fitting the flashing before the roof panels is much easier, and used a temporary spacer the thickness of the glazing to leave room for it.
  8. Glaze the roof and walls. Seal edges and joints.
  9. Hang the door and seal it well. See how to build a greenhouse door that seals well.

For framing basics, our wood-frame greenhouse guide goes through base, walls and roof in more detail.

Moisture, flashing and ventilation

Greenhouse air is humid, and humidity against the house wall can cause staining, mold or rot, especially on wood siding. Good practice is to:

  • Seal and flash all connections to the wall.
  • Cover or protect the wall surface inside the greenhouse with a moisture-resistant finish, such as a masonry paint, or a panel.
  • Ventilate well, so that humidity does not build up. See how to control humidity in a greenhouse.
  • Keep water away from the base of the wall, with sloped ground or drainage.

Place vents at a high point and low point so air moves through. In summer, an attached greenhouse can overheat, so use shade cloth or opening roof vents.

Heating and use

A lean-to often stays a little warmer than a freestanding greenhouse, especially against a heated house, but it will not stay frost-free without help on cold nights. Insulating the end walls and the base helps, and thermal mass against the wall holds heat. See how to heat a greenhouse in winter without electricity and building a year-round solar greenhouse. If you add a heater, take extra care with fuel-burning appliances in a space attached to a living area, and do not vent combustion gases into the house.

The complete guide to diy greenhouse building

How to Build a Backyard Greenhouse
Read the guide

Keep exploring

Guides from other topics

All topics →